Auto repair-How to Flush the Brake System on a 2003 VW Jetta TDI

A brake bleeder (available at auto parts and Interne
breast cyst t stores) is used to remove moisture, and expel contaminated brake fluid from the brak
body shops e system. The brake fluid in a VW should be flushed every 24 months or two (2) years.

Ste
body auto rep
embroidery Furniture air p 1 , Driv
automobile r
stock quotes for pocketpc epair e the vehicle front wheels onto ramps (2)

Step
automotive repair ? , Place the gear selector in Park or 1st Gear.

Step 3 , Place wheel chocks behind the two (2) rear wheels.

Step 4 , Place an oil pan under the passenger,side rear wheel.

Step 5 , Engage the hood lever lever in the cabin compartment.

Step 6 , Raise the engine hood.

Step 7 , Remove the brake reservoir cap (Yellow) by turning counter,clockwise.

Step 8 , Fill the reservoir with fresh VW Dot 4 brake fluid to the fill line.

Step 9 , Fill the reservoir of the brake bleeder pump with fresh VW Dot 4 brake fluid.

Step 10, Attach the plastic tubing (from kit) to the ports of the brake bleeder.

Step 11 , Attach the adapter cap (Red) to the master cylinder reservoir by turning clockwise until tight.

Step 12 , Pump the handle of the brake bleeder pump to pressurize the brake system.

Step 13 , Pump the handle of the pump until a reading between 12 and 15psi is shown on the gauge of the pump.

Step 14 , Place an oil drain pan under the passenger,side rear wheel.

Step 15 , Position the body or use a creeper under the passenger,side rear wheel.

Step 16 , Place a piece of plastic tubing (from kit) on the brake bleeder fitting.

Step 17 , Using a 9mm box wrench, loosen the bleeder fitting by turning counter,clockwise. one (1) turn.

Step 18 , The pressure from the pump will force discolored and contaminated brake fluid to enter the drain pan.

Step 19 , When there are no noticeable air bubbles and the brake fluid turns clear, close the brake bleeder fitting.

Step 20 , Move the drain pan to the drivers,side rear wheel.

Step 21 , Repeat the steps above (14 through 19) on the drivers,side rear wheel.

Step 22 ,Move the drain pan to the passenger,side front wheel.

Step 23 , Repeat the steps above (14 through 19) on the passenger,side front wheel.

Step 24 , Move the drain pan to the drivers,side front wheel.

Step 25 , Repeat the above steps (14 through 19) on the drivers,side front wheel.

Step 26 , Remove the drain pan, plastic tubing, and 9mm wrench from under the drivers,side front wheel.

Step 27 , Pour the contaminated brake fluid into a plastic container.for recycling.

Step 28 , Unscrew the adapter cap (Red) by turning counter,clockwise.

Step 29 , Attach the original brake reservoir cap (Yellow) by turning clockwise.

Step 30 , Remove the hoses to the brake bleeder and adapter and set pump aside.

Step 31 , Have an assistant apply pressure to the brake pedal and check for a firm pedal.

Step 32 , Check for fluid leaks at all four (4) wheels.

Step 33 , Close the engine hood.

Step 34 , Remove rear wheel chocks.

Step 35 , Back vehicle off ramps.

Step 36 , Road test vehicle.

This entry was posted on Friday, May 20th, 2011 at 9:53 am and is filed under automotive repairs. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.

Source: http://www.jx123.info/auto-repair-how-to-flush-the-brake-system-on-a-2003-vw-jetta-tdi.html

road trip tumblebooks google chrome os national university bed bugs the beatles principal